Suppliers of steel products.

p355ml2 material

ASME P-Numbers - welding engineer

Feb 17, 2015 · Engineering assessment is necessary prior to a change in materials. When a base metal with a UNS number Designation is assigned a P-Number, then a base metal listed in a different ASME material specification with the same UNS number shall be considered that P-Number. The table below is a guide and is for instructive purposes only. Base metal grouping system - TWIOnly materials accepted for use in the construction of pressurised components according to the ASME BPVC are listed in QW/QB-422, hence they can be assigned a P-No. If a metal does not appear in the table QW/QB-422 it is considerate unassigned and cannot be grouped under a P-No. If an unlisted material has the same UNS number as a listed

EN 10028 Flat products made of steels for pressure

1.8833 P355ML2 1.8835 P420ML1 1.8837 P460ML1 :EN 10028-6:2009 Flat products made of steels for pressure purposes. Weldable fine grain steels, quenched and tempered COMPARE GRADES 1.8864 P460QL2 1.8865 EN 10216-3 Grade P355NL2 Alloy Steel Seamless Tubes EN 10216-3 Grade P355NL2 Specification. EN Specification alloy steel Tubes are used for high temperature service applications.Seamless Alloy Steel Tubes according to EN 10216-3 Grade P355NL2 are reheated and furnished in full annlealed,isothermal annealed or normalised quenched and tempered condition .EN 10216-3 Grade P355NL2 Alloy Steel Seamless Tubes have a typical chemistry with EN P355NL2 Steel Chemical composition, Metal Properties This page cover the EN P355NL2 steel grades Mechanical Properties, Chemical Element, Cross Reference of Euronorm EN EN P355NL2 Materials, Application Euronorm Structural steel,

EN P355QH Steel Chemical composition, Metal Properties

This page cover the EN P355QH steel grades Mechanical Properties, Chemical Element, Cross Reference of Euronorm EN EN P355QH Materials, Application Euronorm Structural steel, P355ML2,P355ML2 PLATE,P355ML2 STEELBoiler steel sheet P355ML1,low temperature impacting test have to be done at minus 40 .Pressure vessel and boiler steel plates P355ML2 shall be done heat treatment under Thermomechanically rolled when rolling.This treatment offer good cold forming and hot forming properities without negatively affecting the material properties.So these steel P355ML2 is therefore also suitable for cold P355NL1,EN10028-3 Grade P355NL1,P355 NL1 STEEL PLATE P355NL1,EN10028-3 Grade P355NL1,P355 NL1 STEEL PLATE. EN10028 steel grade supersedes the older BS and DIN standards. P355NL1 steel grade is one of grade in En10028-3, which is non alloy and alloy steels with specified elevated temperature properties. P355NL1 grades are used above all for manufacturing boilers, pressure vessels and pipes transporting hot liquids.

P355NL1

Material no. 1.0566 analogic DIN EN 10028-3 Tensile strength class B 1) If N is additionally fixed by means of Nb, Ti or V, the minimum Al content is not determined. If N is 2)Nb + V + Ti 0,12% Notch Impact energy Minimum value of notch impact ener-gy1) [J] at a test temperature of [°C] °C longitudinal [J] transverse [J] +20°C 80 J P355NL2 steel - Steel GradesTool & Die Steels Inc. Stainless Steel, Special Steel, Compressor Blading, Turbine Blading, Superalloy Supplier. P355NL2 Round Bar P355NL2 Flat Bar P355NL2 Hollow Bar P355NL2 Tube / Pipe P355NL2 Sheet / Plate P355NL2 Strip / Coil P355NL2 Wire P355NL2 Forging P355NL2 Tube / Plate for pressure vessel applicationsP355NL2 6 60 mm Normalised - ASME SA516 / ASTM A516:Pressure vessel plates for moderate and lower temperature service with improved toughness Gr 60 6 40 mm As -rolled 6 60 mm Normal ised Gr 65 6 40 mm As -rolled 6 60 mm Normalised Gr 70 6 40 mm As -rolled

Steel Material P355ML2 DIN/EN Pauly Steel-Trader

The material DIN/EN-P355ML2 and its material properties can be viewed here on this page. On this page you will find informations about material called P355ML2 (DIN/EN), as long as we have them.. P355ML2 Steel Material (DIN/EN) Steel Material P355ML2 DIN/EN Pauly Steel-TraderThe material DIN/EN-P355ML2 and its material properties can be viewed here on this page. On this page you will find informations about material called P355ML2 (DIN/EN), as long as we have them.. P355ML2 Steel Material (DIN/EN) en10028 5 p355ml2 material-JIS G3106 Hot Rolled Welded Groupe PRD STEEL Co.:Find professional A283Grade C plate,S235JR steel sheet plate,EN10025-2 steel,Q345B,Boiler and pressure vessel steel,en10028 5 p355ml2 material,manufacturers,suppliers,exporters and sellers in China here.Welcome to buy or wholesale bulk high-quality steel products at the best price from our factory.

p355nl1 material-JIS G3106 Hot Rolled Welded Structure

Sa387 / A387 Gr 11 ASTM A516 Grade 70EN 10028-3 Grade P355NL1 normalized or normalizedSee the chemical composition and physical properties of EN 10028-3 Grade P355NL1 normalized or normalized formed (+N),find alternative materials,and connect with suppliers.P355NL2 steel - Steel GradesTool Die Steels Inc.Stainless Steel,Special Steel,Compressor p355nl1 material-JIS G3106 Hot Rolled Welded Structure Sa387 / A387 Gr 11 ASTM A516 Grade 70EN 10028-3 Grade P355NL1 normalized or normalizedSee the chemical composition and physical properties of EN 10028-3 Grade P355NL1 normalized or normalized formed (+N),find alternative materials,and connect with suppliers.P355NL2 steel - Steel GradesTool Die Steels Inc.Stainless Steel,Special Steel,Compressor substitute P355NL2 Plate whit A516 Gr70 plate in LPG tank substitute P355NL2 Plate whit A516 Gr70 plate in LPG tank ali119 (Materials) (OP) 27 Aug 13 13:32. Hi everybody I have a question about substitute P355 NL2 plate whit A516 Gr 70 plate in Liquid Petroleum Gas (LPG) tank that is designed by BS 7777 standard .

EN 10028:3 P355NL1 and P355NL2 Brown McFarlane

P355NL2 has a more tightly controlled Phosphorus and Sulphur content Mechanical Properties P355NL2 has higher required impact values at all specified temperatures and in

More information


Leave a comment